Start with the deck itself, not the cartridge
The Rega Planar 2 arrives with its RB220 tonearm and Rega Carbon moving magnet cartridge pre-installed, which removes the most intimidating part of a first turntable setup. Before you touch the arm or the cartridge, give the deck a stable, level surface. The Planar 2 measures 447mm wide, 118mm high and 360mm deep and weighs 5.1 kg, so plan for a shelf or stand with enough depth and a little clearance behind for the cables.
A belt-drive turntable depends on a clean path between motor and platter. The Planar 2 uses a 24V synchronous AC motor and a 12mm float glass platter. Check that the belt sits properly around the platter and motor pulley, and that the platter spins freely by hand before you power up. If anything rubs or the belt slips off, stop and re-seat it rather than forcing the motor to correct it.
A first-record sequence for the Planar 2
Work through these in order so each check builds on the last. The supplied catalog does not include a manufacturer tracking-force figure or an anti-skate procedure, so treat those two settings as checks to confirm against the documentation that ships with your deck, not as numbers to guess.
- Level and place the deck: Set the Planar 2 on a rigid, level surface clear of speaker vibration. Confirm all feet carry weight and the plinth does not rock.
- Confirm the belt path and platter: With the deck powered off, check the belt is seated on the motor pulley and the platter sub-platter, then spin the platter by hand to feel for drag.
- Inspect the pre-installed Carbon cartridge: The Rega Carbon MM cartridge comes fitted. Look that the stylus is straight in the body and the headshell screws are snug, without overtightening.
- Set tracking force to the cartridge specification: Use the figure supplied with the Rega Carbon cartridge and a tracking-force gauge. The Planar 2 catalog does not state a value, so do not copy a number from a forum.
- Set anti-skate to match: Apply the anti-skate setting your Rega documentation specifies for the Carbon cartridge. If your deck's anti-skate is fixed or preset, confirm that before adjusting anything.
- Choose 33 1/3 or 45 RPM and lower the arm: The Planar 2 uses a manual speed change for 33 1/3 and 45 RPM. Set the speed before the stylus meets the record, then use the cueing lever to lower the arm gently.
What the Planar 2 gives you to work with
- Rega Planar 2 Turntable with Rega Carbon Cartridge: Pre-installed Rega Carbon moving magnet cartridge and RB220 tonearm with low-friction bearings and a one-piece aluminum arm tube. Because the arm and cartridge are factory-fitted, your setup work focuses on confirming alignment and settings rather than mounting from scratch.

Rega Planar 2 Turntable with Rega Carbon Cartridge - Rega Planar 2 Turntable with Rega Carbon Cartridge: Belt drive with a 24V synchronous AC motor and a 12mm float glass platter. These are the parts to inspect first if speed sounds unstable or the platter drags on the first spin.
- Rega Planar 2 Turntable with Rega Carbon Cartridge: Manual speed change between 33 1/3 and 45 RPM. You select speed yourself, so make it part of your routine before each record rather than after the stylus drops.
Checking the Carbon cartridge without moving it
Rega fits the Carbon cartridge at the factory, and the catalog describes the Planar 2 as designed for simple setup and adjustment. That means your job is verification, not a full alignment from a blank headshell. Sight down the front of the cartridge: the stylus should sit centered and perpendicular to the record surface, and the cartridge body should look square in the headshell.
If the stylus looks visibly skewed or the cartridge sits at an obvious angle, do not compensate with tracking force or anti-skate. Those settings cannot correct a misaligned body. Since the supplied information does not include a cartridge-alignment procedure or protractor specification, the honest next step is to consult Rega's documentation or a dealer rather than improvise. A small, careful check now is better than a first record that skates or distorts.
First-record tips that actually change the outcome
- Clean the record before the stylus, not after: A dusty first play pushes debris into the stylus. Brush the record surface before lowering the arm so the Carbon stylus meets a clean groove.
- Use the cueing lever every time: Dropping the arm by hand risks a bent stylus or a scratched lead-in. The lever gives you a controlled descent on the first record and every one after.
- Keep the lid and mat consistent: Play with the same lid position each time. Changing it mid-session alters what the deck sits on and how it behaves, which makes small setup problems harder to trace.
- Listen to one familiar record first: A track you know well makes it easier to notice skipping, channel imbalance or speed oddities while the setup is still fresh in your mind.
When to stop and recheck
If the first record skips on loud passages, the stylus may be riding too light or the deck may not be level. If it sounds dull in one channel, revisit the cartridge and tonearm connections before adjusting anything else. If speed drifts, return to the belt and platter check rather than reaching for tracking force, which has nothing to do with motor speed.
The Planar 2's combination of a rigid plinth, glass platter and RB220 arm is intended to reduce vibration and support stable tracking, but those qualities depend on a correct starting setup. Make one change at a time, then replay the same passage so you can hear whether the change helped.
Setup checks versus settings you should not guess
- Confirm from the deck itself: Level, belt seating, platter freedom, stylus condition, speed selection and cable connections are all things you can verify directly.
- Confirm from Rega documentation: Tracking force and anti-skate values for the Carbon cartridge are not in the supplied catalog, so use the manufacturer's figures rather than a remembered number.
- Leave alone unless something is wrong: The factory-fitted cartridge alignment is best left as delivered unless you see a clear problem; a needless re-alignment introduces more risk than it removes.


